1330 Series Driveshaft Yoke

Description: GM 27 spline, GM 32 spline, Mopar 30 spline Tremec TKO 31 spline, T-5 & 3550 28 spline

15:1 Steering Rack

18:1 Steering Rack

302-351 iron heads

Description: These are brand new Ford iron heads that are complete and ready to install.

Installation Notes: On 302's the head bolts will need special washers or ARP head bolts

31 spline Aluminum Driveshaft for M/T 4.6

Description: This also fits 79-93 5.0 Mustang with 31-spline TKO Tremec.

Installation Notes: Fits 79-93 5.0 Fits 96-2004 Mustang Fits 94-2004 Mustang with Tremec TKO but NEEDS a driveshaft spacer kit.

Part Number: M 4602 J

347ci Crate Engine - M-6007-C347

Description: 450hp @ 6000, 400 ft lbs @ 4900

Installation Notes: Needs 28oz. flywheel or flexplate. Reverse rotation water pump installed.

Part Number: M 6007 C347

4282010 VE 525 CFM VAC SEC

460 ci Crate Engine 550HP - M-6007-F460

4-Into-4 Exhaust Gaskets (Pair)

Description: Used between the FFR 4-into-4 Headers and Sidepipes.

5 Lug 11 inch rotors

Description: These 5 lug rotors replace the 11 inch 4 lug Mustang GT rotors 1986- 1993 except COBRA.

Installation Notes: New inner & outer bearings & seals are available plus grease caps, lock nuts & washers.

Part Number: M-1102 C

5-Lug Rear Disc Brake Conversion Kit New orders from 8/29/07 forward

Description: Includes axles, 10.5" rotors, calipers, brackets and hardware.

Installation Notes: options: drilled/slotted rotor, black caliper(limited availability), 11.65" rotor.

7.5" Front shifter

Description: Moves shifter to front location 7.5" off bellhousing

Installation Notes: Requires extensive work to transmission Must be bought at time of purchase

8.8 axle housing vent

Description: This vent fits into the 8.8 axle tube.

8.8 Ford Rear Gears: 3.73/3.55/4.30/4.11 in stock only

Description: Fits 8.8 ford rear ends

Installation Notes: Free shipping with install kit. Purchase of complete installation kit $89.00.

Related Parts: Install kit, Axles, Rear end

8.8 straight axle rearend 3.73 Trac lock rearend assembly minus axle

8.8" finned aluminum rearend cover

Description: 8.8" finned aluminum rearend cover with fill & magnetic drain plug. Main cap girdle. Optional "COBRA" engraved $35.00 extra.

8.8" Rear 13" vented rotor rear brakes

Description: Billet aluminum caliper brackets with Wilwood hat & vented 13" rotors & Cobra rear calipers in red or black.

87-93 Front Rotors - 5 Lug (Pair)

Description: New 5 lug 11" rotors for 1986-1993 4 lug to 5 lug conversion. NOTE: Does not fit 1993 COBRA.

90 Degree Oil Filter Adapter

Adjustable push rod

Description: Universal brake push rod. Requires drilling a 3/8" hole.

ALUMINUM BIG BLOCK CHEVY OPEN CHAMBER HEADS & INTAKE

Description: This pair of heads are from a 482" IMSA CORVETTE. These are used heads that have extensive port work that will need at least a good inspection and probably rebuilding.

Installation Notes: Piston to valve clearance must be checked. I have the 482" short block that was part of the engine if wanted complete. includes GM dual plane intake.

ALUMINUM T-5 BELLHOUSING

Description: FITS 6 BOLT FORD 289, 302 & 351-W & C

AMC Tremec TKO-500

Installation Notes: This REQUIRES a special aluminum or Lakewood steel bellhousing.

AMC Tremec TKO-600

Installation Notes: This REQUIRES a special aluminum or Lakewood steel bellhousing.

Big Block 429 / 460 Alternator Bracket

Description: 429 /460 alternator mount kit & pulleys

Billet Oil Filter Mount

Part Number: 22595

Brake Bias Adjuster

Description: In cockpit brake bias adjuster. Fits Wilwood, CNC & Tilton dual master cylinder kits. Allows front to rear bias adjustments with the turn of a dash mounted knob.

C-5 T-56

Description: This new T-56 fits all C-5 vettes. Why rebuild when new is available.

Cleco Kit

Description: Cleco pliers and 20 1/8" removable aligning pins

Clutch alignment tool

Description: Hardened tool steel clutch alignment tool specify GM/Ford, 10, or 26 spline

Cold air kit dual snorkle air filter

Description: Cold air kit dual snorkle air filter Add ram air to your car

Collapsible steering shaft & U-joint with quick release hub

Description: Fits MK I & MK II

Coverlay dash cover

Description: 18-601 81-87 Chevy & GMC Pickup, 81-91 Blazer, Suburban & Jimmy $65.00 18-602 73-80 Chevy & GMC Pickup, Suburban & Jimmy $65.00

CS Shelby 427 timing cover

Description: Factory timing covers were plain-Jane looking die cast aluminum. Dress up your FE with a Shelby FE aluminum timing cover. The as-cast surface, with Carroll Shelby's polished logo dresses up any engine. Cover fits Shelby 427 Alloy FE block and factory cast iron FE blocks.

Driveshaft loop kit

Description: Universal driveshaft loop

Installation Notes: May require cutting & drilling. Torque bolts to 30 ft lbs

Edelbrock 60379 Performer RPM Heads

Description: Bolt on aluminum Edelbrock heads. Uses bolt down pedistal mount rockers

Part Number: 60379

External slave & billet fork conversion

Description: Developed by Mike Forte, this billet external slave & fork actuate the stock throw-out bearing. This is available for Chevrolet, FE Ford, 429-460 BB Ford & SB Ford.

Part Number: FORD & CHEVY

FFR Driveshaft kit

Description: These are custom made driveshaft kits complete with all new parts needed to install.

Installation Notes: FFR driveshafts have many standard lengths. FFR MK I & MK II are the same with a small block. I stock many and build to fit your car at the same cost. Please specify transmission used, rearend used, model car & engine size.

Related Parts: yoke, u-joint, rear flange, flange bolts

Firewall adjustable quadrant kit

Description: This is one of my designs that everyone has copied. It uses the stock cable and adjusts the clutch at the firewall with the twist of the threaded adjuster

Ford 157 Tooth 28 oz billet flywheel

Description: Pre-1981 302 engines 289 and 351 engines using 157T flywheels. Meets SFI 1.1.

Part Number: M-6375 A302

Ford 157 tooth 50oz. flywheel

Description: Fits 82 up HO 5.0 with 50 oz. imbalance. Nodular iron and has 10.5" Mustang clutch pattern

Installation Notes: On 302 engines flywheel bolts require sealant on threads. Uses metric clutch bolts & dowels for clutch installation.

Part Number: M-6375 B302

Ford 157 tooth Aluminum flywheel

Description: 157-tooth 28.2 oz.-in. Pre-1981 302 engines and 351 engines using 157T flywheel. Reduced rotating mass for faster engine acceleration in race applications. Meets SFI 1.1.

Part Number: M-6375 A302A

FORD 5.0 FORK 93 DOWN

Description: 89-93 STOCK FORD MUSTANG FORK. UNLIKE SOME OF OUR COMPETITORS OFFERINGS THIS FORK COMES WITH THE SPRING CLIP AND NEEDS NOTHING FROM YOUR ORIGINAL FORK

Part Number: CLUTCH FORK 5.0

Ford Tremec TKO-500

Installation Notes: This REQUIRES a special aluminum or Lakewood steel bellhousing.

Part Number: TCET 4615

Ford Tremec TKO-600 .64OD

Description: TKO-600 .64OD

Installation Notes: Requires either a steel or aluminum bellhousing

Related Parts: Fork, pivot ball, yoke & driveshaft spacer

Part Number: TCET 5008

Ford Tremec TKO-600 .82OD roadrace

Installation Notes: This REQUIRES a special aluminum or Lakewood steel bellhousing.

Related Parts: bellhousing, flywheel, clutch kit, clutch fork, pivot ball & cable & driveshaft spacer

Part Number: TCET 4617

Fork, Cable and Quadrant kit (does not include fork extension)

Description: Ford cable & clutch fork, Fortes firewall adjustable quadrant kit. Optional clutch fork extension for McLeod or Lakewood steel bellhousing $24.00

Forte

Description: Billet aluminum firewall adjuster. Designed to fit 83-93 Mustang retaining the OEM clutch cable

Forte's Clutch Alingment tool

Description: Steel clutch alignment tool 10 and 26 spline gm or ford availible

Part Number: tool

Forte's Power Steering Pump Mounting kit

Description: Billet aluminum bracket. Bracket surounds the pump and bolts to the water pump fits 302/351 smallblock fords

Part Number: P/S BRACKET

FRPP 9MM Spark Plug Wire Set - 302/351 Blue

FRPP 9MM Spark Plug Wire Set - 302/351 Red

FRPP 9MM Spark Plug Wire Set - Modular 4.6 Blue

FRPP Harmonic Damper Kit for 5.0 50 OZ.

Description: 93 & earlier 5.0 balancer & timing tab

Related Parts: balancer bolt, timing cover, water pump, pulleys

Fuel pickup, fuel filter & fittings with adel clamps

Description: Fits Mustang fuel tank with fittings for fuel filter that go to 3/8" steel fuel line (FFR supplied) and Adel clamps

Fuel Pressure Gauges - 0-15, 0-60, 0-100 & 0-1500 psi

Description: These guages are chrome plated housing & bezel, liquid filled pressure gauges. These are available in 0-15psi, 0-60psi, 0-100psi & 0-1500psi.

Installation Notes: These all have a 1/8" male npt fitting straight out of the back of the gauge.

Fuel Sender Pigtail for Mustang sender. (Also have pigtail for EFI fuel pump)

GM F-Late TKO 600 Conversion

GM F-Late TKO-500 Conversion

Description: Convert your TKO-500 to a F-Late transmission

Installation Notes: This conversion is best done with a Ford TKO-500 26-spline Tremec.

Part Number: GM F-Late TKO-500 conv

GM Syncromesh oil

Description: Semi-synthetic manual transmission oil recommended by Tremec for proper lubrication and sycro operation.

GM T-56 six speed universal fit

Description: This T-56 bolts to both a T-5 or a Muncie/Borg Warner bellhousing. It comes with a 2.97 1st, 2.07 2nd, 1.43 3rd 1:1 4th, .80 5th & .62 6th.

Installation Notes: NOTE*** Transmission tunnel modifications are most likely needed. This T-56 does not include a bellhousing. It has a 26-spline input and a 27-spline output.

GM TKO-600

GM TKO-600 TCET 4618

Description: GM TKO-600RR 2.87, 1.89, 1.28, 1:1, .82 5th

Part Number: TCET 4618

GM TKO-600 TCET 5009

Description: GM TKO-600 2.87, 189, 128, 1:1, .64 5th.

Installation Notes: Bolts to GM bellhousing using Muncie, Borg Warner T-10 & Saginaw bolt pattern.

Part Number: TCET 5009

HD T5 Z Transmission & bellhousing Module

Description: Heavy Duty T5 Z, 5 speed transmission including M-6392 E bellhousing.

Installation Notes: M-6392-E bellhousing. Has 10 spline input shaft. 28 Spline output shaft. 2.95 first gear with a .63 fifth gear.

Part Number: 1352-251

Hose Shear

Description: Cutter for Earls braided stainless hose

Installation Notes: wrap in duct tape cut hose

Hydraulic External Slave For Steel bellhousing

Description: Special price availible when purchaced with bellhousing only

Part Number: Ford & Chevy

Installation kits for rear end gears

Description: Includes ALL bearings /seals/and shims as well as pinion nut and crush collar SPECIAL Ask about special $$ with rear gears

IRS 11.65" bracket kit

Description: Fits IRS T-bird & Lincoln to convert to 11.65" Cobra rear rotors using Mustang rear calipers. Includes mounting hardware.

IRS Knuckle, brakes & CV shaft

Description: Complete rear IRS minus center section. Includes new knuckles, Cobra 5 x 4.5" bolt circle hubs, 10.5" rotors, loaded calipers, stainless hoses & banjo bolts. The NEW CV shaft assemblies are assembled but require your FFR supplied CV shafts sent to RAXLES.

Part Number: IRS CV SHAFT, KNUCKLES & BRAKES

Lokar E-Brake Handle Assembly

LS-1 T-56 1386 000 017

LS-1 T-56 to a stock GM bellhousing

Description: This plate kit will mount a stock LS-1 T-56 to a stock GM bellhousing (Muncie, Saginaw or Borg Warner T-10). This will include a Chevy pilot and use a stock linkage & throw out bearing.

LT-1 T-56 1386 000 016